Gas Lift Valves
Technical Specification
| Manufacturer | Valve Name | Type | Port | R Value | Diameter Size | Remark |
|---|---|---|---|---|---|---|
| Schlumberger (Camco) | SLB/Camco R20-O2B | IPO | 16 | 1 | .""",,, | |
| ELC | ELC Fortress 16 | IPO | 16 | 1 | .""",,, | |
| Mako | Mako Sonic | Orifice | 16 | 1 | .""",,, | |
| Schlumberger | NOVA 10 | Venturi | 24 | 1 | This is a 1 inch orifice valve with venturi type chokes. The valve reaches critical flow very quickly. Be sure to operate this valve in the critical flow range! If it is operating in the differential range"," very large flow rate changes will occur with very little change in either casing or tubing pressure. Call Schlumberger for other port sizes.""",, | |
| Schlumberger | NOVA 10 | Venturi | 18 | 1 | This is a 1 inch orifice valve with venturi type chokes. The valve reaches critical flow very quickly. Be sure to operate this valve in the critical flow range! If it is operating in the differential range"," very large flow rate changes will occur with very little change in either casing or tubing pressure. Call Schlumberger for other port sizes.""",, | |
| Schlumberger | NOVA 10 | Venturi | 14 | 1 | This is a 1 inch orifice valve with venturi type chokes. The valve reaches critical flow very quickly. Be sure to operate this valve in the critical flow range! If it is operating in the differential range"," very large flow rate changes will occur with very little change in either casing or tubing pressure. Call Schlumberger for other port sizes.""",, | |
| Schlumberger | NOVA 10 | Venturi | 8 | 1 | This is a 1 inch orifice valve with venturi type chokes. The valve reaches critical flow very quickly. Be sure to operate this valve in the critical flow range! If it is operating in the differential range"," very large flow rate changes will occur with very little change in either casing or tubing pressure. Call Schlumberger for other port sizes.""",, | |
| Schlumberger | NOVA 15 | Venturi | 22 | 1 | This is a 1 inch orifice valve with venturi type chokes. The valve reaches critical flow very quickly. Be sure to operate this valve in the critical flow range! If it is operating in the differential range"," very large flow rate changes will occur with very little change in either casing or tubing pressure. Call Schlumberger for other port sizes.""",, | |
| Schlumberger (Camco BK TC) | Camco BK TC Seat | Other | 12 | Coments""",,, | ||
| Flowco | Flowco TP-1 OC16 | IPO | 16 | ,,, | ||
| Flowco | Flowco WP1.0 Monel | IPO | 12 | ,,, | ||
| Priority | Priority IPOR-2 | IPO | 24 | ,,, | ||
| Schlumberger (Camco) | Camco LNM-31R | Other | 21 | This is a high performance valve with large tubing effect factor. The valve will always throttle closed on reductions in tubing pressure. The flow performance changes markedly for small changes in tubing pressure. The valve will vibrate a small amount near the closing event. Repeated opening and closing could result in damage to the seat.""",,, | ||
| Schlumberger (Camco) | Camco LNM-31R | Other | 29 | This is a high performance valve with large tubing effect factor. The valve will always throttle closed on reductions in tubing pressure. The flow performance changes markedly for small changes in tubing pressure. The valve will vibrate a small amount near the closing event. Repeated opening and closing could result in damage to the seat.""",,, | ||
| Altec (JMI) | Altec AT1-CF | Other | 10 | This is a 1 inch IPO valve with a twist. A choke is placed UPSTREAM of the port. The choke controls the rate of flow while allowing full upstream pressure to work on the bellows. Generous flow rate and small throttling range.""",,, | ||
| Altec (JMI) | Altec AT1-CF | Other | 14 | This is a 1 inch IPO valve with a twist. A choke is placed UPSTREAM of the port. The choke controls the rate of flow while allowing full upstream pressure to work on the bellows. Generous flow rate and small throttling range.""",,, | ||
| Altec (JMI) | Altec AT1-VL | Differential | 8 | This is a differential valve that allows a different setting for the opening and closing. For example"," set the valve to close at 250 psig differential and then set the reopening for 125 psig. The re-opening pressure was VERY accurate during the testing. The closing pressure was not. Check the performance curves to see that the closing usually occurs at less than the set pressure.""",, | ||
| Altec (JMI) | Altec AT1-VL | Differential | 12 | This is a differential valve that allows a different setting for the opening and closing. For example"," set the valve to close at 250 psig differential and then set the reopening for 125 psig. The re-opening pressure was VERY accurate during the testing. The closing pressure was not. Check the performance curves to see that the closing usually occurs at less than the set pressure.""",, | ||
| Weatherford (McMurray-Macco) | Weatherford RPDV | Differential | 10 | This is a 1-1/2 inch differential valve. The re-opening pressure is set independent of the closing differential. With large chokes and high differentials"," the valve closes at less differential than set at. When open it behaves like an orifice valve.""",, | ||
| Weatherford (McMurray-Macco) | Weatherford RPDV | Differential | 14 | This is a 1-1/2 inch differential valve. The re-opening pressure is set independent of the closing differential. With large chokes and high differentials"," the valve closes at less differential than set at. When open it behaves like an orifice valve.""",, | ||
| Schlumberger (Camco) | Camco WFM-14R | Pilot | 10 | This is a 1 inch pilot valve. The valve is spring set and is not temperature sensitive. When the pilot opens"," the power section also opens and allows flow. When open it behaves like an orifice valve. Very large flow rates.""",, | ||
| Petrospect | Petrospect Line | Orifice | 12 | ,,, | ||
| Shell | Shell Bubbles | Orifice | 10 | ,,, | ||
| Shell | Shell Bubbles | Orifice | 16 | ,,, | ||
| Weatherford (McMurray-Macco) | Weatherfrd R-1CF | Other | 16 | This is an IPO valve with a choke upstream of the port. The port is a 5/16. The listed ports are actually the choke sizes.""",,, | ||
| PTC | PTC 15 IPO | IPO | 12 | This is a high pressure valve(5000 psig). Flow is generous. The valve has a downstream orifice of the same size as the port. Valve closes very quickly.""",,, | ||
| Weatherford (McMurray-Macco) | Weatherford R-1 | IPO | 10 | 0.066 | 1 | This is a 1 inch IPO valve. The loadrate tested very high and the effective stem travel was less than expected. Expect a little less flow than the BK.""",,, |
| Weatherford (McMurray-Macco) | Weatherford R-1 | IPO | 16 | 0.165 | 1 | This is a 1 inch IPO valve. The loadrate tested very high and the effective stem travel was less than expected. Expect a little less flow than the BK.""",,, |
| Weatherford (McMurray-Macco) | Weatherford R-1B | IPO | 10 | 0.066 | This is the same as the Weatherford R-1 except with a bottom latch. The loadrate is a lot lower than the R-1 and flow rate is much higher for the same set pressures.""",,, | |
| Weatherford (McMurray-Macco) | Weatherford R-1B | IPO | 16 | 0.165 | This is the same as the Weatherford R-1 except with a bottom latch. The loadrate is a lot lower than the R-1 and flow rate is much higher for the same set pressures.""",,, | |
| Weatherford (McMurray-Macco) | Weatherford R-2 | IPO | 12 | 0.038 | 1.5 | This is a 1-1/2 inch IPO wireline retrievable valve. Performance is very predictable. Maximum set pressure of 1800 psig.""",,, |
| Weatherford (McMurray-Macco) | Weatherford R-2 | IPO | 20 | 0.103 | 1.5 | This is a 1-1/2 inch IPO wireline retrievable valve. Performance is very predictable. Maximum set pressure of 1800 psig.""",,, |
| Weatherford (McMurray-Macco) | McMurry C-2 | IPO | 16 | 0.066 | 1.5 | This is a 1-1/2 inch IPO tubing retrievable valve. Performance is nearly identical to the wireline retriavable. High flow rates and small throttling portion. The valve has a very high sensitivity to casing pressure.""",,, |
| Weatherford (McMurray-Macco) | Macco R-1D | IPO | 12 | 0.094 | The loadrate is a little high but this is not unusual. Valve acts predictable and no vibration or chatter was evident during operation. The valve tends to stay open and flow at maximum capacity until about 100 psig above closing tubing pressure and then closes quickly.""",,, | |
| Weatherford (McMurray-Macco) | Macco R-1D | IPO | 20 | 0.255 | The loadrate is a little high but this is not unusual. Valve acts predictable and no vibration or chatter was evident during operation. The valve tends to stay open and flow at maximum capacity until about 100 psig above closing tubing pressure and then closes quickly.""",,, | |
| Weatherford (McMurray-Macco) | Macco RF-1 H | PPO | 12 | 0.094 | This is a spring loaded PPO valve with a cross-over port. The H indicates a high rate spring. Maximum set pressure is 950 psig. Cross-over ports work quite nicely. It never choked in the open position during any tests. Flow rate through the valve is very reasonable.""",,, | |
| Weatherford (McMurray-Macco) | Macco RF-1 L | PPO | 10 | 0.066 | This is a spring loaded PPO valve with a cross-over port. The L indicates a low rate spring. Maximum set pressure is 750 psig. Cross-over ports work quite nicely. It never choked in the open position during any tests. Flow rate through the valve is very reasonable.""",,, | |
| Weatherford (McMurray-Macco) | Macco RF-1 L | PPO | 16 | 0.165 | This is a spring loaded PPO valve with a cross-over port. The L indicates a low rate spring. Maximum set pressure is 750 psig. Cross-over ports work quite nicely. It never choked in the open position during any tests. Flow rate through the valve is very reasonable.""",,, | |
| Weatherford (McMurray-Macco) | McMurry C-1 | IPO | 12 | 0.094 | 1 | This is a 1 inch tubing retrievable valve. Low loadrate and generous flow.""",,, |
| Weatherford (McMurray-Macco) | Weatherford RH-1 | IPO | 24 | ,,, | ||
| Weatherford (McMurray-Macco) | McMurry C-1 | IPO | 16 | 0.165 | 1 | This is a 1 inch tubing retrievable valve. Low loadrate and generous flow.""",,, |
| Weatherford (McMurray-Macco) | Weathrfrd RDDK-2 | Orifice | 12 | Dump-kill valve. Good performance.""",,, | ||
| Weatherford (McMurray-Macco) | Weathrfrd RDDK-2 | Orifice | 20 | Dump-kill valve. Good performance.""",,, | ||
| Weatherford (McMurray-Macco) | Weathrfrd RDDK-2 | Orifice | 28 | Dump-kill valve. Good performance.""",,, | ||
| Weatherford (McMurray-Macco) | Weathrfrd RO-2B | Orifice | 8 | Typical orifice valve. Flow is better than RDO-20 but still less than Thornhill-Craver.""",,, | ||
| Weatherford (McMurray-Macco) | Weathrfrd RO-2B | Orifice | 12 | Typical orifice valve. Flow is better than RDO-20 but still less than Thornhill-Craver.""",,, | ||
| Weatherford (McMurray-Macco) | Weathrfrd RO-2B | Orifice | 16 | Typical orifice valve. Flow is better than RDO-20 but still less than Thornhill-Craver.""",,, | ||
| Weatherford (McMurray-Macco) | Weatherford R-2 | IPO | 24 | 0.147 | 1.5 | This is a 1-1/2 inch IPO wireline retrievable valve. Performance is very predictable. Maximum set pressure of 1800 psig.""",,, |
| Weatherford (McMurray-Macco) | Weathrfrd RDDK-1 | Orifice | 24 | Dump-kill valve. Only two ports tested (12 and 16). Flow rates for other ports are interpolated. Flow is very good.""",,, | ||
| Weatherford (McMurray-Macco) | Weathrfrd RO-2J | Orifice | 28 | 1.5 | 1-1/2 inch orifice valve with redesigned backcheck. Check seals after erosion tests. Performance is typical.""",,, | |
| Weatherford (McMurray-Macco) | Wethrfrd RFC-1BL | PPO | 8 | 0.043 | This PPO valve has a milled cross-over port. Valve will close at set pressure regardless of upstream pressure.""",,, | |
| Weatherford (McMurray-Macco) | Wethrfrd RFC-1BL | PPO | 12 | 0.094 | This PPO valve has a milled cross-over port. Valve will close at set pressure regardless of upstream pressure.""",,, | |
| Weatherford (McMurray-Macco) | Wethrfrd RFD-1BL | PPO | 12 | 0.094 | This valve has drilled crossover ports. Depending on the upstream pressure"," the valve may not close at the set pressure.""",, | |
| Weatherford (McMurray-Macco) | Wethrfrd RO-2HV | Orifice | 20 | ,,, | ||
| Weatherford (McMurray-Macco) | Weathrfrd RO-2B | Orifice | 20 | Typical orifice valve. Flow is better than RDO-20 but still less than Thornhill-Craver.""",,, | ||
| Weatherford (McMurray-Macco) | Weatherford RH-2 | IPO | 16 | 0.066 | ,,, | |
| Weatherford (McMurray-Macco) | Weatherford RO-1 | Orifice | 10 | Typical orifice valve.""",,, | ||
| Weatherford (McMurray-Macco) | Weatherford RO-1 | Orifice | 16 | Typical orifice valve.""",,, | ||
| Weatherford (McMurray-Macco) | Weatherford RO-1 | Orifice | 24 | Typical orifice valve.""",,, | ||
| Weatherford (McMurray-Macco) | Weatherford RO-2 | Orifice | 16 | Typical orifice valve.""",,, | ||
| Weatherford (McMurray-Macco) | Weatherford RO-2 | Orifice | 24 | Typical orifice valve.""",,, | ||
| Weatherford (McMurray-Macco) | Weathrfrd RDDK-2 | Orifice | 8 | Dump-kill valve. Good performance.""",,, | ||
| Weatherford (McMurray-Macco) | Weathrfrd RDDK-1 | Orifice | 8 | Dump-kill valve. Only two ports tested (12 and 16). Flow rates for other ports are interpolated. Flow is very good.""",,, | ||
| Weatherford (McMurray-Macco) | Weathrfrd RDDK-1 | Orifice | 12 | Dump-kill valve. Only two ports tested (12 and 16). Flow rates for other ports are interpolated. Flow is very good.""",,, | ||
| Weatherford (McMurray-Macco) | Weathrfrd RDDK-1 | Orifice | 20 | Dump-kill valve. Only two ports tested (12 and 16). Flow rates for other ports are interpolated. Flow is very good.""",,, | ||
| Schlumberger (Camco) | Camco BKO-3 | Orifice | 8 | Typical orifice valve. Flow is less than Thornhill-Craver predicts. The 52 port is dual ported valve. Latest test of 8/64ths show flow improvement.""",,, | ||
| Schlumberger (Camco) | Camco BK | IPO | 8 | 0.043 | It has a high load rate for an IPO valve and performs predictably. The high loadrate causes less flow than for other IPO valves with lower loadrates.""",,, | |
| Schlumberger (Camco) | Camco BK | IPO | 12 | 0.094 | It has a high load rate for an IPO valve and performs predictably. The high loadrate causes less flow than for other IPO valves with lower loadrates.""",,, | |
| Schlumberger (Camco) | Camco BK | IPO | 20 | 0.255 | It has a high load rate for an IPO valve and performs predictably. The high loadrate causes less flow than for other IPO valves with lower loadrates.""",,, | |
| Schlumberger (Camco) | Camco BKF-12 | PPO | 16 | 0.165 | This is an updated version of the SRF-10. Flow rate is about the same. The valve stays open until closing. This is an improvement over the SRF-10.""",,, | |
| Schlumberger (Camco) | Camco BKF-12C | PPO | 16 | 0.165 | ,,, | |
| Schlumberger (Camco) | Camco BKF-6 | PPO | 16 | 0.165 | The test data was collected by Camco and is of rather poor quality. All of the 1/8 port tests showed less than 70 Mscfd for all pressure ranges. I suspect something was wrong with the valve or the test skid. The 3/16 tests were a little better but closing pressures were poorly defined. Considering the quality of the data"," only the simplified correlation was used.""",, | |
| Schlumberger (Camco) | Camco BKO-3 | Orifice | 12 | Typical orifice valve. Flow is less than Thornhill-Craver predicts. The 52 port is dual ported valve. Latest test of 8/64ths show flow improvement.""",,, | ||
| Schlumberger (Camco) | Camco BKO-3 | Orifice | 16 | Typical orifice valve. Flow is less than Thornhill-Craver predicts. The 52 port is dual ported valve. Latest test of 8/64ths show flow improvement.""",,, | ||
| Schlumberger (Camco) | Camco BKO-3 | Orifice | 20 | Typical orifice valve. Flow is less than Thornhill-Craver predicts. The 52 port is dual ported valve. Latest test of 8/64ths show flow improvement.""",,, | ||
| Schlumberger (Camco) | Camco BKR-5 | PPO | 12 | 0.094 | Be careful with this valve. It may not close! The cross-over port arrangement allows choking to occur at the cross-over ports thus isolating the bellows from downstream pressure. The pressure ratio at which this happens is port size dependent. If the ratio of PvoT/Piod is less than the following numbers", the valve will not close on reductions in downstream pressure. 1/8 - .345, 3/16 - .618," 1/4 - .867 | |
| Schlumberger (Camco) | Camco DCR-DK | Orifice | 32 | Dump-kill valve. Only two ports tested. Flow is generous.""",,, | ||
| Schlumberger (Camco) | Camco BKR-5 | PPO | 16 | 0.165 | Be careful with this valve. It may not close! The cross-over port arrangement allows choking to occur at the cross-over ports thus isolating the bellows from downstream pressure. The pressure ratio at which this happens is port size dependent. If the ratio of PvoT/Piod is less than the following numbers", the valve will not close on reductions in downstream pressure. 1/8 - .345, 3/16 - .618," 1/4 - .867 | |
| Schlumberger (Camco) | Camco J-20 | Orifice | 16 | This is NOT the standard conventional IPO valve. It was modified to act like an orifice. Performance is typical.""",,, | ||
| Schlumberger (Camco) | Camco BKR-5 | PPO | 8 | 0.043 | Be careful with this valve. It may not close! The cross-over port arrangement allows choking to occur at the cross-over ports thus isolating the bellows from downstream pressure. The pressure ratio at which this happens is port size dependent. If the ratio of PvoT/Piod is less than the following numbers", the valve will not close on reductions in downstream pressure. 1/8 - .345, 3/16 - .618," 1/4 - .867 | |
| Schlumberger (Camco) | Camco RDO-20 | Orifice | 16 | Typical orifice valve. Flow is less than Thornhill-Craver predicts.""",,, | ||
| Schlumberger (Camco) | Camco RDO-20 | Orifice | 20 | Typical orifice valve. Flow is less than Thornhill-Craver predicts.""",,, | ||
| Schlumberger (Camco) | Camco RDO-20 | Orifice | 24 | Typical orifice valve. Flow is less than Thornhill-Craver predicts.""",,, | ||
| Schlumberger (Camco) | Camco R-25P1 | PPO | 24 | 0.147 | Data collected for DPC and donated to VPC. Am not sure what the difference is between this and R-25P. Tested a long time ago and my memory is short.""",,, | |
| Schlumberger (Camco) | Camco RDO-20 | Orifice | 10 | Typical orifice valve. Flow is less than Thornhill-Craver predicts.""",,, | ||
| Schlumberger (Camco) | Camco J-20 | Orifice | 20 | This is NOT the standard conventional IPO valve. It was modified to act like an orifice. Performance is typical.""",,, | ||
| Schlumberger (Camco) | Camco J-20 | Orifice | 28 | This is NOT the standard conventional IPO valve. It was modified to act like an orifice. Performance is typical.""",,, | ||
| Schlumberger (Camco) | Camco J-40 | Orifice | 16 | This is NOT the standard conventional IPO valve. It was modified to act like an orifice. Performance is typical.""",,, | ||
| Schlumberger (Camco) | Camco R-25P1 | PPO | 20 | 0.103 | Data collected for DPC and donated to VPC. Am not sure what the difference is between this and R-25P. Tested a long time ago and my memory is short.""",,, | |
| Schlumberger (Camco) | Camco R-20 | IPO | 8 | 0.017 | VPC Tested. Very good performance. Small throttling zone. Repeatability testing indicates new valves are within +/-10%.""",,, | |
| Schlumberger (Camco) | Camco R-25P1 | PPO | 16 | 0.066 | Data collected for DPC and donated to VPC. Am not sure what the difference is between this and R-25P. Tested a long time ago and my memory is short.""",,, | |
| Schlumberger (Camco) | Camco R-25P1 | PPO | 12 | 0.038 | Data collected for DPC and donated to VPC. Am not sure what the difference is between this and R-25P. Tested a long time ago and my memory is short.""",,, | |
| Schlumberger (Camco) | Camco R-25P | PPO | 20 | 0.103 | 1.5 | Standard 1-1/2 inch PPO valve. Data collected for DPC and donated to VPC.""",,, |
| Schlumberger (Camco) | Camco R-25P | PPO | 12 | 0.038 | 1.5 | Standard 1-1/2 inch PPO valve. Data collected for DPC and donated to VPC.""",,, |
| Schlumberger (Camco) | Camco R-20 | IPO | 24 | 0.147 | VPC Tested. Very good performance. Small throttling zone. Repeatability testing indicates new valves are within +/-10%.""",,, | |
| Schlumberger (Camco) | Camco R-20 | IPO | 16 | 0.066 | VPC Tested. Very good performance. Small throttling zone. Repeatability testing indicates new valves are within +/-10%.""",,, | |
| PTC | PTC 15 Safelift | Orifice | 22 | ,,, | ||
| PTC | PTC 15 SafeliftS | Orifice | 24 | ,,, | ||
| PTC | PTC 15 IPO | IPO | 12 | 0.043 | This is a high pressure valve(5000 psig). Flow is generous. The valve has a downstream orifice of the same size as the port. Valve closes very quickly.""",,, | |
| PTC | PTC 10 Safelift | Orifice | 12 | ,,, | ||
| PTC | PTC 10 Safelift | Orifice | 20 | ,,, | ||
| Merla | Merla N-17R | IPO | 8 | 0.017 | This valve has an externally charged bellows which means it retains ALL stem travel regardless of set pressure. The valve reacts predictably with a small amount of backcheck chatter near the closing event. Nothing to worry about.""",,, | |
| Merla | Merla N-17R | IPO | 16 | 0.066 | This valve has an externally charged bellows which means it retains ALL stem travel regardless of set pressure. The valve reacts predictably with a small amount of backcheck chatter near the closing event. Nothing to worry about.""",,, | |
| Merla | Merla N-17R | IPO | 24 | 0.147 | This valve has an externally charged bellows which means it retains ALL stem travel regardless of set pressure. The valve reacts predictably with a small amount of backcheck chatter near the closing event. Nothing to worry about.""",,, | |
| Baker Hughes | Baker BOF-1.5 | Orifice | 20 | This is a high performance orifice valve. Flow rate is very high. The valve reaches critical flow at very low pressure differentials.""",,, | ||
| Baker Hughes | Baker BOF-1.5 | Orifice | 24 | This is a high performance orifice valve. Flow rate is very high. The valve reaches critical flow at very low pressure differentials.""",,, | ||
| Altec (JMI) | Altec AT1-O | Orifice | 24 | 1 | This is a 1 inch orifice valve. Flow rates approach the Thornhill/Craver equation.""",,, | |
| Altec (JMI) | Altec AT1-O | Orifice | 10 | 1 | This is a 1 inch orifice valve. Flow rates approach the Thornhill/Craver equation.""",,, | |
| Altec (JMI) | Altec AT1-O | Orifice | 14 | 1 | This is a 1 inch orifice valve. Flow rates approach the Thornhill/Craver equation.""",,, | |
| Altec (JMI) | Altec AT1-O | Orifice | 18 | 1 | This is a 1 inch orifice valve. Flow rates approach the Thornhill/Craver equation.""",,, | |
| Altec (JMI) | Altec AT2-CF | IPO | 12 | 0.038 | This is an IPO valve with a choke upstream of the main port. Valve tends to flow a little more than normal IPO valve at the closing.""",,, | |
| Altec (JMI) | Altec AT2-CF | IPO | 20 | 0.103 | This is an IPO valve with a choke upstream of the main port. Valve tends to flow a little more than normal IPO valve at the closing.""",,, | |
| Altec (JMI) | Altec AT2-CF | IPO | 28 | 0.1952 | This is an IPO valve with a choke upstream of the main port. Valve tends to flow a little more than normal IPO valve at the closing.""",,, | |
| Altec (JMI) | Altec AT1-O | Orifice | 20 | 1 | This is a 1 inch orifice valve. Flow rates approach the Thornhill/Craver equation.""",,, | |
| Altec (JMI) | JM20-HRglO-R | Orifice | 12 | 1.5 | Developed by Shell and manufactured by JMI. Brand name is FAST-TEC(TM). This is a 1-1/2 inch High Reliability retrievable orifice valve. Passed erosion tests and held bubble tight. Flow performance is typical.""",,, | |
| Altec (JMI) | JM20-HRglO-R | Orifice | 20 | 1.5 | Developed by Shell and manufactured by JMI. Brand name is FAST-TEC(TM). This is a 1-1/2 inch High Reliability retrievable orifice valve. Passed erosion tests and held bubble tight. Flow performance is typical.""",,, | |
| Altec (JMI) | JM-HRC | Orifice | 20 | 1 | Developed by Shell and manufactured by JMI. Brand name is FAST-TEC(TM). This is a 1 inch conventional High Reliability check valve. This valve passed numerous erostion tests and held bubble tight. Flow performance is excellant.""",,, | |
| Altec (JMI) | JM-HRglO-R | Orifice | 12 | 1 | Developed by Shell and manufactured by JMI. Brand name is FAST-TEC(TM). This is a 1 inch retrievable High Reliability orifice valve. Passed erosion tests and held bubble tight. Flow performance is typical.""",,, | |
| Altec (JMI) | JM-HRglO-R | Orifice | 20 | 1 | Developed by Shell and manufactured by JMI. Brand name is FAST-TEC(TM). This is a 1 inch retrievable High Reliability orifice valve. Passed erosion tests and held bubble tight. Flow performance is typical.""",,, | |
| TUALP | TUALP R-20 | IPO | 12 | 0.038 | The valve data was collected at TUALP and does not include loadrate or flow coefficient data. Bellows is internally charged and this valve is very susceptable to loss of stem travel with increases in set pressure. The valve exhibits a fair amount of valve chatter near the closing event. Repeated openning and closing could result in damage to the seat. Performance is typical.""",,, | |
| TUALP | TUALP R-20 | IPO | 20 | 0.103 | The valve data was collected at TUALP and does not include loadrate or flow coefficient data. Bellows is internally charged and this valve is very susceptable to loss of stem travel with increases in set pressure. The valve exhibits a fair amount of valve chatter near the closing event. Repeated openning and closing could result in damage to the seat. Performance is typical.""",,, | |
| TUALP | TUALP R-20 | IPO | 24 | 0.147 | The valve data was collected at TUALP and does not include loadrate or flow coefficient data. Bellows is internally charged and this valve is very susceptable to loss of stem travel with increases in set pressure. The valve exhibits a fair amount of valve chatter near the closing event. Repeated openning and closing could result in damage to the seat. Performance is typical.""",,, | |
| None | 1 Inch IPO | IPO | 16 | 0.165 | 1 | This is an average of all the 1 inch IPO valves.""",,, |
| None | 1 Inch IPO | IPO | 10 | 0.066 | 1 | This is an average of all the 1 inch IPO valves.""",,, |
| None | 1 Inch IPO | IPO | 20 | 0.255 | 1 | This is an average of all the 1 inch IPO valves.""",,, |
| None | 1 Inch IPO | IPO | 12 | 0.094 | 1 | This is an average of all the 1 inch IPO valves.""",,, |
| JMI | JM-OR | Orifice | NA | Orifice""",,, | ||
| Camco | ED-30R | Dummy | 1/4 | NA | Equalizing Dummy Valve""",,, | |
| Camco | EK-1 | Dummy | NA | NA | Equalizing Dummy Valve is used to",,, | |
| Camco | DKO-2 | Orifice | 1/8-3/8 | NA | ,,, | |
| Camco | CEV | Dummy | NA | NA | Equalizing Dummy Valve""",,, | |
| Camco | C-31R | Chemical Injection Valve | 3/16 | NA | The Camco-Merla* Spring Loaded C-31R chemical injection",,, | |
| Camco | BKO-3 | Orifice | 1/8-5/16 | NA | ,,, | |
| Camco | BKFS | Circulating Valve | 1/16-7/16 | NA | Circulating Valve""",,, | |
| Camco | BKF - 12 | PPO | 1/8-1/4 | NA | The BKF-12 is bellows actuated", spring,, | |
| Camco | BKEO | Orifice | 1/8-5/16 | NA | Equalizing Orifice Valve in",,, | |
| Camco | BK-1 Carbide | PPO | 8 | 0.068 | Baker Series (Bellows valves)""",,, | |
| Camco | BK Normal | IPO | 20 | 0.255 | Baker Series (Bellows valves)""",,, | |
| Camco | BK Normal | IPO | 12 | 0.094 | Baker Series (Bellows valves)""",,, | |
| Camco | BK Normal | IPO | 8 | 0.042 | Baker Series (Bellows valves)""",,, | |
| Camco | BK Carbide | IPO | 16 | 0.187 | Baker Series (Bellows valves)""",,, | |
| Camco | BK Carbide | IPO | 8 | 0.068 | Baker Series (Bellows valves)""",,, | |
| JMI | JM-20 Carbide | IPO | 12 | 0.037 | ,,, | |
| JMI | JM-BK Carbide | IPO | 20 | 0.329 | ,,, | |
| JMI | JM-BK Carbide | IPO | 14 | 0.138 | ,,, | |
| JMI | JM-BK Carbide | IPO | 10 | 0.066 | ,,, | |
| Camco | DK-1 | Dummy | NA | NA | Dummy""",,, |
Petrotopic is all about Petroleum Engineering Topics
Social Media
📘 Petrotopic Article on LinkedIn
Discover insights, innovations, and trends in petroleum engineering directly from Petrotopic.
➤ View Full Article on LinkedIn